Original U.S. WWII Blade Marked M3 Fighting Knife by Utica Cutlery with 1943 Dated M6 Scabbard

Item Description

Original Item: Only One Available. This is a fine condition WWII M3 U.S. fighting knife, made by the desirable maker, Utica Cutlery Co. With the marking on the blade, this is the more desirable "2nd Pattern", which was replaced quickly by the 3rd pattern with markings on the crossguard. It comes complete in a correct 1943 dated M6 leather belt scabbard, which is in great shape. These fighting knives were preferred by American infantry during World War Two for hand to hand combat.

This knife is very early production, indicated by the maker information being stamped and dated directly on the blade: U.S. M3 - UTICA. The 6 3/4 inch spear point blade is in very good used condition, with much of the original finish present. It has wear around the edges, and the main edge has been sharpened, and is still quite sharp. There has been some light pitting removed on the tip, due to oxidation from the scabbard. Please consult the pictures for the fine details.

The handle and stacked leather grip are in good but used condition, with no major issues or cracking. The crossguard is still in the correct shape, straight with a forward bend at the top for the thumb. The bottom of the pommel shows the U.S. "Flaming Bomb" ordnance proof mark and correct peened over tang.

The original M6 leather scabbard is in great shape, and still clearly marked U.S. M6 / MILSCO / 1943 just under the stapled throat, with a "flaming bomb" proof below. It has a lovely aged leather look, with a bit of cracking and dry rot in places. There is a bit of tearing where the frog meets the scabbard, and it shows a lot of wear. The original retaining strap broke away, and this was replaced with one from an M8 scabbard, along with some leather to reinforce the rivet. There is also a repair on the back where the frog meets the scabbard body, where the rivets and stitching have torn out. Definitely a scabbard that saw long service. This is the original scabbard designed for this knife, which was then replaced with the thermoplastic resin impregnated cotton duck M8/M8A1 scabbards, which were also used with the M4 bayonet.

A very nice example of an early issue blade marked M3 knife from a desirable maker, complete with the correct scabbard. Ready to add to your WWII edged weapon collection!

Blade length: 6 3/4”
Overall length: 11 1/2”
Scabbard length: 8"
Crossguard: 2 1/4”

History of the M3 Fighting Knife

The M3 fighting knife or M3 trench knife was an American military combat knife first issued in March 1943. The M3 was originally designated for issue to soldiers not otherwise equipped with a bayonet. However, it was particularly designed for use by elite or 'shock' forces in need of a close-combat knife such as airborne troops and Army Rangers, and these units received priority for the M3 at the start of production. As more M3 knives became available in 1943 and 1944, the knife was issued to other soldiers such as Army Air Corps crewmen and soldiers not otherwise equipped with a bayonet, including soldiers issued the M1 Carbine or submachine gun.

The M3 was manufactured by a number of U.S. knife and cutlery manufacturers during the war. Manufacturers known to have made the M3 under wartime contract include the Aerial Cutlery Co., W. R. Case & Sons Cutlery Co., Imperial Knife Co., PAL Cutlery Co., Camillus Cutlery Co., Robeson (ShurEdge) Cutlery Co., Kinfolks Inc., Utica Cutlery Co., and H. Boker & Co.

The M3 was developed as a replacement for the World War I-era U.S. Mark I trench knife, primarily to conserve strategic metal resources. The prototype for what would become the M3 was evaluated in December 1942 by the civilian board of directors of the Smaller War Plants Corporation Board (SWPC) against another competing design, the US Marine Corps' 1219C2 fighting utility knife. However, while the specified priority steel supplies for both knives were available, the M3's lower production cost compared to that of the 1219C2 convinced the SWPC board of directors to approve the M3 prototype for quantity production.

Though the M3 had competed with the USMC 1219C2 for approval by the Army, the M3, unlike the Marine Corps knife, was not a dual-purpose weapon designed for both close combat (fighting knife) and general use (utility knife). As the U.S. Catalog of Standard Ordnance Items of 1943 clearly explained:

The Trench Knife M3 has been developed to fill the need in modern warfare for hand-to-hand fighting. While designated for issue to soldiers not armed with the bayonet, it was especially designed for such shock units as parachute troops and rangers.

The M3 was first issued to U.S. Army soldiers in March 1943, with the first knives going to elite units such as airborne troops and the U.S. Army Rangers. Despite ordnance descriptions of the knife as being designed for hand-to-hand warfare, the M3 did not receive universal praise as a close-quarters fighting knife upon issue to combat units. While the knife itself was generally well-made and balanced (some paratroopers and rangers mastered the art of using the M3 as a throwing knife), the long narrow dagger-like steel blade, designed to economize on priority steel requirements, was best used as a thrusting or stabbing weapon, and performed less well when used for slashing strokes. Reports of blade failures on M3s in service increased as soldiers began to use their trench knives for ordinary utility tasks such as opening ammo crates and food ration tins, a role for which the M3 had not been designed. Some soldiers also found the M3's cutting edge to be difficult to maintain in the field. As issued, the blade's secondary or false edge was intentionally sharpened and beveled for only a portion of its length, leaving an unsharpened spine on the top of the blade in an effort to stiffen the relatively narrow blade. This limited the usefulness of the M3 when employed for backhand slashing strokes.

The M3 replaced the OSS dagger in service in 1944.

After U.S. Army ordnance began developing a proprietary bayonet for use on the M1 carbine, it was realized that the new carbine bayonet, which already incorporated the M3 blade design and leather-wrap grip, could also replace the M3 in service in a secondary role as a fighting knife. The carbine bayonet, now designated the Bayonet, U.S. M4, was added to the Company Table of Organization in June 1944, and the M3 was declared to be a limited standard ordnance item, with supplies to be issued until exhausted. Nevertheless the final M3 production run did not take place until August 1944, by which time 2,590,247 M3 trench knives had been produced.

At termination of production in August 1944, the M3 trench knife had one of the shortest production and service records of any U.S. combat knife. However, the M3's blade design continued in U.S. military service in the form of the U.S. M4, M5, M6, and M7 bayonets.

  • This product is available for international shipping.
  • Eligible for all payments - Visa, Mastercard, Discover, AMEX, Paypal & Sezzle


Cash For Collectibles